Z-World XP8900 Manual de usuario Pagina 92
- Pagina / 114
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
PK2100
F-8 s Appendix F: PLCBus
There are 4-bit and 8-bit drivers. The 4-bit drivers employ the following
calls.
void eioResetPlcBus()
Resets all expansion boards on the PLCBus. When using this call,
make sure there is sufficient delay between this call and the first access
to an expansion board.
LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB.
void eioPlcAdr12( unsigned addr )
Specifies the address to be written to the PLCBus using cycles
BUSADR0, BUSADR1, and BUSADR2.
PARAMETER: addr is broken into three nibbles, and one nibble is
written in each BUSADRx cycle.
LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB.
void set16adr( int adr )
Sets the current address for the PLCBus. All read and write operations
access this address until a new address is set.
PARAMETER: adr is a 16-bit physical address. The high-order
nibble contains the value for the expansion register, and the remaining
three 4-bit nibbles form a 12-bit address (the first and last nibbles must
be swapped).
LIBRARY: DRIVERS.LIB.
void set12adr( int adr )
Sets the current address for the PLCBus. All read and write operations
access this address until a new address is set.
PARAMETER: adr is a 12-bit physical address (three 4-bit nibbles)
with the first and third nibbles swapped.
LIBRARY: DRIVERS.LIB.
void eioPlcAdr4( unsigned addr )
Specifies the address to be written to the PLCBus using only cycle
BUSADR2.
PARAMETER: addr is the nibble corresponding to BUSADR2.
LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB.
- Users Manual 1
- CONTENTS 3
- Software Reference 5-1 4
- Contents s v 5
- ABOUT THIS MANUAL 7
- Terms and Abbreviations 8
- Table 3. Icons 9
- PK2100x s About This Manual 10
- PK2100 OVERVIEW 11
- PK2100 Overview 12
- PK2100 Features 13
- PK2110 Features 13
- PK2120 Features 13
- PK2130 Features 13
- Options and Upgrades 13
- 1-4 s PK2100 Overview 14
- GETTING STARTED 15
- Initial PK2100 Setup 16
- Establishing Communication 17
- Running a Sample Program 17
- 2-4 s Getting Started 18
- I/O CONFIGURATIONS 19
- PK2100 Inputs and Outputs 20
- I/O Configurations s 3-3 21
- Universal Inputs 22
- Temperature Sensor 23
- +10-V reference 23
- Digital Inputs 24
- Counter 1 25
- Counter 2 25
- Jumper H7 installed 27
- Relay Outputs 29
- Digital Outputs 30
- Inductive 31
- D.C. in D.C. in 31
- Digital output 31
- 3-14 s I/O Configurations 32
- SYSTEM DEVELOPMENT 33
- Programming 34
- Virtual Driver 35
- Virtual Driver Services 36
- System Development s 4-5 37
- Virtual Driver Variables 38
- System Development s 4-7 39
- Downloading Code 40
- Attainable Baud Rates 41
- Z180 Serial Ports 41
- 4-10 s System Development 42
- SOFTWARE REFERENCE 43
- Driver Software 44
- Analog Input 45
- 5-4 s Software Reference 46
- Analog Output 47
- High-Speed DMA Counter 48
- Battery-Backed Clock 49
- 5-8 s Software Reference 50
- Software Reference s 5-9 51
- EEPROM Read / Write 52
- Flash EPROM Write 52
- Communication 53
- subdirectory 54
- Program Description 55
- TROUBLESHOOTING 57
- Out of the Box 58
- Dynamic C Will Not Start 59
- Dynamic C Loses Serial Link 59
- PK2100 Resets Repeatedly 59
- Common Programming Errors 60
- APPENDIX B: SPECIFICATIONS 61
- Hardware Dimensions 62
- Table B-4 64
- Header Pins Description 65
- Connectors 67
- POWER MANAGEMENT 69
- Power Failure Interrupts 70
- Heat Sinking 71
- C-4 s Power Management 72
- I/O MAP AND 73
- INTERRUPT VECTORS 73
- Address Name Description 74
- Table D-2. Write Registers 76
- Table D-3. Read Registers 78
- Address Bits Symbol Function 78
- Interrupt Priorities 80
- APPENDIX E: EEPROM 81
- Address Definition 82
- Field Calibration 84
- APPENDIX F: PLCBUS 85
- PLCBus Overview 86
- PLCBus Header 87
- Table F-2. PLCBus Registers 88
- Appendix F: PLCBus s F-5 89
- A1 A2 A3 Meaning 90
- Expansion Bus Software 91
- F-8 s Appendix F: PLCBus 92
- Appendix F: PLCBus s F-9 93
- F-10 s Appendix F: PLCBus 94
- Appendix F: PLCBus s F-11 95
- F-12 s Appendix F: PLCBus 96
- BATTERY 97
- G-2 s Appendix G: Battery 98
- Battery Cautions 99
- G-4 s Appendix G: Battery 100
- BOARD LAYOUT 101
- Index s I-1 103
- PK2100I-2 s Index 104
- Index s I-3 105
- PK2100I-4 s Index 106
- Index s I-5 107
- PK2100I-6 s Index 108
- Index s I-7 109
- PK2100I-8 s Index 110
- Index s I-9 111
- PK2100I-10 s Index 112
- Printed in U.S.A 113
© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales